Concrete repairs in St George
Updated October 2026
Cracked driveway panels, a sunken path that trips visitors, concrete flaking off around rusting steel. St George concrete deals with tree roots in older streets, salt air along the bay, stormwater running down the river slopes and decades of sun, and sooner or later it shows. We connect you with experienced, insured local concreters who can tell you honestly whether your concrete needs a repair or a replacement. We are a referral service, not a concreting business, so the advice you get comes from someone who has seen the job.
The three most common problems
Cracked concrete
Hairline shrinkage cracks are normal and mostly cosmetic. Wider cracks, cracks that step in height or cracks that keep growing point to movement underneath. Tree roots from established street trees in suburbs like Bexley, Kogarah and Penshurst are a common cause, along with washed-out bases and ground movement.
Sunken concrete
Panels sink when the base under them was poorly compacted or has eroded. On sloping blocks toward the Georges River, stormwater running under a driveway can wash out the base. On sandy ground near the bay, poor compaction is the usual story. Options range from grinding a trip edge, to slab jacking where a panel is lifted by pumping material underneath, to cutting out and repouring the affected panels.
Spalling concrete
Spalling is the surface flaking or drummy patches that appear when moisture and salt reach the reinforcing steel and it rusts and expands. It is common along the Botany Bay side at Brighton-Le-Sands, Ramsgate, Sans Souci and Dolls Point, and on older apartment balconies and carparks. Treating spalling properly means cutting back to sound concrete, treating or replacing the steel and patching with a repair mortar, not just skimming over the top.
Repair or replace?
A rough rule many contractors use is that once repairs approach half the cost of replacement, or the slab is moving rather than just worn, replacement wins. Patches on a driveway rarely match the surrounding concrete, so replacement also wins on looks. For a tired but sound slab, resurfacing or a sealed coloured topping can renew it for less than a repour. If you replace, see our concrete driveways and paths and patios pages.
What repairs cost
Pricing varies more than new work because every repair is different, so treat any figure as a guide until a contractor sees the job. For full panel replacement, published 2026 rates for plain concrete run roughly $75 to $150 per square metre laid, plus demolition of the old concrete at around $30 to $100 per square metre. Small patch and grinding jobs are often charged by the hour or as a minimum call-out. Get a fast quote and compare.
How a panel replacement runs
1. Saw cut the damaged section at the nearest joints
2. Break out and remove the old concrete
3. Fix the cause, recompact the base, cut roots or improve drainage
4. New formwork, steel mesh and dowels into adjoining panels where appropriate
5. Pour, finish to match the surrounding surface as closely as possible, cure and joint
Fixing the cause is the step that separates a lasting repair from a repeat job. A panel repoured over the same failed base will sink again.
Strata and apartment repairs
Hurstville, Rockdale, Kogarah and Wolli Creek have a lot of apartment buildings, and their carparks, ramps, paths and balconies need repairs too. Strata work usually needs insurance certificates, a written scope for the committee or building manager, and access booked around residents. Mention it is a strata job when you request a quote so it goes to a suitable contractor. See commercial concreting for larger common-property work.
Licensing and approvals
In NSW, residential building work worth more than $5,000 (labour and materials, including GST) must be done by a licensed contractor, and larger repair and replacement jobs reach that figure. Ask for the licence number and check it before you sign. For repairs to a driveway crossing the footpath, check with your council, as approval is usually needed for work on that strip.
Site factors that move the price
- Access for removing broken concrete, hard on steep blocks and narrow inner-suburb lots
- Tree roots that must be cut and barriers installed
- Drainage work needed to stop water undermining the base
- Matching decorative finishes such as exposed aggregate, which takes extra care
- Small pour volumes, which cost more per square metre
Do not wait on safety issues
A trip edge on a path or a crumbling step is a liability as well as a hazard. Grinding a trip edge is a quick, cheap fix that buys time while you plan the bigger repair.
Ready for honest advice on your cracked or sunken concrete? Get a fast quote.
Frequently asked questions
Are hairline cracks in concrete a problem?
Usually not. Fine shrinkage cracks are normal as concrete cures. Watch for cracks that widen, step in height or let water through. These suggest movement and are worth a professional look.
Can a sunken concrete panel be lifted?
Often yes. Slab jacking pumps material under the panel to raise it, and suits sound panels that have sunk evenly. Badly cracked panels are better cut out and repoured.
What causes concrete spalling near Botany Bay?
Salt-laden moisture penetrates the concrete and rusts the reinforcing steel. Rust expands and pops the surface off. Homes and apartment buildings along the bay see it most, and proper repair means treating the steel, not just patching the surface.
Will a repaired patch match my existing concrete?
Rarely perfectly. Concrete colour changes with age and weathering. Contractors can get close, or cut back to joint lines so the new panel reads as deliberate rather than patched.